Tech Forum Questions

Sorry Clarence but I suspect this is going to be difficult to impossible. I have used white vinegar to neutralize and remove the deposits and corrosion but:

1.  The corrosion/battery acid and possibly the addition of the vinegar acid end up removing the coatings on metal parts which makes them less robust.
2.  A watch has extremely small parts and the connections may be ruined already. You need to first take the watch completely apart to see the extent of the damage inside it. If the damage is confined to the battery port you may be in luck.

Use a Q-tip cotton swab with some vinegar on it; place it on the residue/corrosion and keep it there long enough to soak into the residue. Then twist the swab to remove the residue. If more removal is needed repeat this process. You can also use dry swabs to remove more residue if no more vinegar is needed.

Once all the residue is removed, you should use a contact cleaner/lubricator/protector fluid to coat the battery contacts.

If the watch is really expensive, I would bring it to a watch maker shop and pay for the cleaning. At home, for my electronics, I use dish washing liquid — pour a few drops onto the corrosion and let it soak overnight. This usually dissolves the acidic corrosion. You can still clean with a Q-tip, then rinse and carefully dry the watch.

Baking soda is a good acid neutralizer. It will stop further damage, but does nothing to restore damage done. The oxide already deposited will need to be removed with a scraping tool of some kind, and will without doubt, reveal damage.

First, use a Q-tip and 90%+ isopropyl alcohol to clean the corrosion — do NOT immerse or flood the watch with alcohol! When you’re done with this step, CAREFULLY use canned air to GENTLY dry the cleaned area.

Then, apply a paste made from baking soda and water to the cleaned areas and let it sit for 20-30 min. The baking soda will stop any corrosive action by any corrosion not removed by the first alcohol cleaning.

Finally, use a dry q-tip to remove as much of the baking soda paste as possible, then finish cleaning any residue with q-tips and alcohol. Again, use the canned air to dry the cleaned area and ensure you don’t get any of the paste blown into the watch.

Take your time in cleaning and pasting — the leaked corrosion tends to be very tenacious, etc. and sometimes difficult to remove. Be aware that you’ll use lots of q-tips as you’ll want fresh ones when they get dirty and ratty.

This makes me think of the automotive MAF (Mass Air Flow) sensor.

Essentially it is a small diameter resistive wire suspended in the air duct. A small current flows through the wire, and is warmed up that way. The wire resistance will change (due to the cooling effect) of air flowing over it. So at a specific regulated voltage, and used in a breathing tube, the current will change depending on breathing.

It could possibly even distinguish between breathing in, and out (due to assumption that air going in would be cooler than air going out).

You’ll need a strain gauge band to wrap around your subject’s chest and a detector that’ll take the (very small!) varying voltage generated by the strain gauge and turn it into something useful.

Mr. Dixon desires to amplify electrical signals originated in plant stems and roots. This is a perfect application for an instrumentation amplifier circuit. Instrumentation amplifiers amplify the voltage difference appearing between two sources, neither of which is referenced to ground.

Basic information on instrumentation amplifiers and lots of applications bulletins from IC manufacturers such as Analog Devices, Texas Instruments and Intersil can be found if the phrase “instrumentation amplifier applications” is used as an internet search argument.

Very old Legacy computers used different physical addresses for the LPT port. Try some of the other addresses. The most common ones:

• Logical parallel port 1: I/O port 0x3BC, IRQ 7 (usually in monochrome graphics adapters)
• Logical parallel port 2: I/O port 0x378, IRQ 7 (Addon I/O cards or using a controller built into the mainboard)
• Logical parallel port 3: I/O port 0x278, IRQ 5 (Addon I/O cards or using a controller built into the mainboard)

Note: More modern computers can require interrogating the OS or an interrupt call. Also a device driver may be required.

This is great! The humble printer port lives! Here’s my guess as to what is happening in your situation.

You are using the OUT command and the syntax is OUT Port#, Data where Port# is the address of the parallel port, typically &H3BC, &H378 or &H278. You need to find the address for your particular configuration. In the older machines, the Parallel Port was on a separate plug-in card and there should be jumpers on the card for setting the address.

The reason why the dot matrix printer works is because the print routine in use calls for the data to be sent to LPT1: instead of the port address. The computer’s BIOS translates the LPT1: to your port’s address. You are bypassing this function by going directly to the port via the OUT command. You should be able to go into the PC’s BIOS setup and find the port address assigned to LPT1:, then use that address in your OUT command.

Or open up the PC, find the parallel port setup jumpers and set them so the port address matches the address on your Compaq. Note that if you do change the card’s address, you’ll probably have to go into the BIOS and make the change there too.

May I suggest getting hold of the book Parallel Port Complete by Jan Axelson? A veritable boatload of information, including an example program for identifying what ports are installed in Chapter 4.

Do a Google search for partester by Kellyware (freeware). The information displayed and ability to toggle the outputs will give you the troubleshooting information you need. The program was created in support of the CNC program Kcam that uses the parallel port to control these machines.

Depending on your computer, LPT1 may have one of two addresses. LPT1= 03BC hex, DATABYTE 956, STATUSBYTE 957, CONTROLBYTE 958 or LPT1= 0378 hex, DATABYTE 888, STATUSBYTE 889, CONTROLBYTE 890. Whichever one you are using, try the other one.

I would check the printer port settings in the BIOS. The LPT port should be set up for bi-directional communication. “Standard parallel” will not work. ECP should work. Different BIOSs have different options for the port settings. P. S. My dad and my brother were both pharmacists.

There are 3 types of printer ports for PCs, Standard, EPP and EC. Check out the Wikipedia article at https://en.wikipedia.org/wiki/Parallel_port There may be an issue with LPT1 not being at the address expected, see the Interfaces and Access sections. It may also be possible to use one of the DSR or DTR lines from the serial port to control the SCR.

Although the early BASIC language gave instructions for direct access to hardware such as LPT and COM ports, operating system and BIOS variations can interfere and limit direct control.

For an excellent source of parallel-port information, get a copy of the 2006 edition of Jan Axelson’s book, Parallel Port Complete. You’ll find much helpful information therein. Also find guidance here: [url=http://retired.beyondlogic.org/spp/parallel.htm]http://retired.beyondlogic.org/spp/parallel.htm[/url].

Many eons ago I did something similar, using 80286 vintage computers to control a weather station via LPT1. The BASIC routine needed to know the address of the LPT port, which on my machines was always 888 (decimal). I do remember that Compaq machines used a different address, but unfortunately I can’t recall what it was.

I suggest you consider migrating your control system to an Arduino or Raspberry Pi platform. I have done this myself, and never looked back. The new boards are so much smaller, cheaper, less power hungry, more user friendly from the standpoint of hardware control, and there is exhaustive online support.

There is no need to buy a chip programmer or use assembly language. I have not been so excited about electronics since discovering solderless prototpying and integrated circuits 30 years ago.

I have used a D-Link KVM to switch only the monitor. There is button on the front for switching. If you use the KVM to switch everything, you can use a keyboard hotkey for switching.

You can get displayport switch boxes that will do what you need, or you can simply use a standard KVM and only connect the video signals. The KVM doesn't care whether the keyboard and mouse signals are present.

See a displayport switch at:
https://www.monoprice.com/product?p_id=24568&gclid=Cj0KCQiAhrbTBRCFARIsACY7MW24DFsN7mnNHfaBDyoCt5fwNLQRz5D_f5LWa9UlfHVgznaYYWMevacaAlf7EALw_wcB

Also, search displayport switch at amazon.com. There are several listed.

I am using Matter Control. By far this has been the easiest right out of the box. In most cases you do not need to go into settings, except to change resolution. When first installed you will need to enter type and print area of your printer. The only complaint I have ever had is there is no Emergency Stop. You can stop/pause the print, but in some cases you just have to kill the job. Good luck!

I purchased my first 3d printer — the Tevo Tarantula — last February, and I have enjoyed every minute of it. The Tevo has a large support group on facebook (if you’re into that — I’m not) as well as on Thingiverse. I would also point you to Thingiverse to find dang near any model you could ever want — including a whole multitude of upgrades for the Tarantula. I myself have uploaded a few of my own modifications (my username there is ‘rebeltaz’).

The only drawback to low cost printers is that a lot of the controller boards are not able to properly handle the current required for a heated bed. You will want to get a MOSFET interface board — the cbd-3d being a popular model — to offload the current drain to a more suitable controller.

As for software, you are going to find diehard recruiters for all the available packages. Me personally, I prefer Sketchup for functional models, since I already had experience with that program. You will need to add a plugin called SolidInspector to ensure watertight (i.e. solid) models suitable for 3d printing. Another good free alternative I use is Blender. This program seems better suited for more organic models, although you can use it for functional designs.

If you lean towards “cloud based” software (I do not) there are various alternatives in that category as well — TinkerCAD being a popular one.

You will also need a slicer program whose job it is to generate the g-code understood by the printer from your 3d model. Simplify3D is a relative expensive example, but both Slic3r and Cura are excellent freely available alternatives. I personally prefer Cura due to it’s more user friendly interface.

Finally, (well, in closing anyway) I would also recommend that you think about getting a Raspberry Pi later on and load it with OctoPi. This will allow you to access and control your printer wirelessly from anywhere on your local network, or even around the world if you so desire.

If you ever have any questions or need any help/advice, I am always willing to help newcomers to this wonderful hobby. You can find me on Thingiverse. Hope to see you there!

Henry, no need to build anything.  Just visit the following on-line retailers and purchase a ready-built convertor:

Amazon.com: https://www.amazon.com/StarTech-SVID2COMP-S-Video-Composite-Adapter/dp/B0000BZ2WC/ref=sr_1_5?ie=UTF8&qid=1514583833&sr=8-5&keywords=s+video+to+composite+adapter

Newark.com: http://www.newark.com/mcm/33-0004/s-video-to-composite-video-adapter/dp/43W7844

Frys.com: https://www.frys.com/product/4712139?site=sr:SEARCH:MAIN_RSLT_PG

Frys.com: https://www.frys.com/product/4301795?site=sr:SEARCH:MAIN_RSLT_PG

There are many, many more places that sell these convertors (do an internet search).  The above suggestions are My Preferred on-line A/V vendors.

These units plug directly into your S-video input (male plug), then use a composite cable from the RCA jack to your monitor's Yellow (composite) RCA input jack.

I've used these items before and they work very well! Do not expect "s-video" resolution from the composite input, but at least you'll be able to enjoy your S-VHS recordings.

Finally, consider getting a DVD Recorder like the Toshiba DVR430 (https://www.amazon.com/Toshiba-DR430-DVD-Recorder/dp/B0038JECKY).  This unit will DIRECTLY accept an S-Video input and stereo line-level inputs so you can transfer your S-VHS tapes to DVD (tapes eventually DO wear out! single-sided DVD record only!).  With the HDMI output, you can DIRECTLY connect it to an HDMI input of your LED TV and "pass through" your S-VHS tape programming to your TV through the recorder.  I have a similar unit (Toshiba DVR620KU - this unit also has a standard VHS recorder/player) and it works great for when I need to record broadcast programming.

VHS tapes deteriorate and fail. The machine is unlikely to be repairable due to parts availability and even replacing the machine is major dollars. For family videos, you really want to keep, I would suggest converting the tapes to a more modern format say DVD or a standard video file format.

Modern PCs have an HDMI port that connects to your TV. You can buy hardware you can use to convert them to PC format yourself or contract a service to do it for you. You can buy an S-Video to HDMI converter if you want to go that way. I will say that my HD TV had issues with playing the tapes due to slight variations in the timing signals from the tape which caused blackouts and breakups in the picture. You may have better luck with your TV.

You need a composite video, left audio and right audio to HDMI adapter. I believe S-video is composite video/audio basically as a digital TV of new would see it. Search eBay or Amazon for it. You’ll need cables with those names too.

If you go to Wikipedia.org and look up S-Video, there is a simple schematic for an s-video to composit adapter.

S-video carries the luminance (B&W picture) and the chroma (color information) on separate wires as opposed to composite video which mixes them together to be carried by a single wire. There are fancier ways to combine the chroma and luma signals but often you can get acceptable results by simply tying them together, most of the inexpensive S-video to composite adapter cables do just that.

No point in building at this price- As usual, eBay is your friend:

https://www.ebay.com/itm/S-Video-4-Pin-to-Composite-Video-RCA-AV-Converter-Cable-c10-new/252047502746

You can buy S-Video to Composite video adapters from amazon.com, walmart.com, newegg.com, monoprice.com, and brick and mortar places like Fry's Electronics, Best Buy and others. I've even seen one at Target.

You can get them as small adapters, boxes you have to plug cables into or even built into a cable, with a S-Video DIN receptacle on one end and an RCA plug at the other. Plug "S-Video to Composite video adapters" into google.com.

This adapter will do the trick: https://smile.amazon.com/Electop-S-Video-Female-Composite-Adapter/dp/B01DKR7CAK/ref=sr_1_6?s=electronics&ie=UTF8&qid=1517188486&sr=1-6&keywords=s-video+to+composite or, to build it yourself: http://suhastech.com/do-it-yourself-make-a-svideo-to-rca-composite-cable-adapter/

S-Video (also known as Y/C), refers to a video signal where the two components of the television signal (the sync and “luma” or “Y” which can be thought of as the black-and-white portion of the television signal, and “chroma” or “C” which includes the color information of the television signal) are carried on separate conductors inside a common cable. This is done to improve the quality of the television signal compared to a composite signal where the two components are combined and carried on a signal conductor.

Simple S-video to Composite adapters exist that combine the Y and C signals together with some capacitance and maybe resistance added for coupling and level-matching. Being that the required components are so small, they are often packaged together in an S-video to Composite coupling adapter or a short cable.

They are widely available and quite affordable. Two sources:

www.amazon.com/Electop-S-Video-Female-Composite-Adapter/dp/B01DKR7CAK
www.amazon.com/StarTech-SVID2COMP-S-Video-Composite-Adapter/dp/B0000BZ2WC

If you want to build your own S-video to composite converter, the following is a good place to start.
Y-ground—+ +— RCA/composite ground C-ground—+ Y—+ +— RCA/composite video C—||—+ 470pF
Note that going in the reverse direction is more difficult — using the adapter to convert composite video to S-video will result in a viewable picture, but the quality will be reduced due to the adapters inability to cleanly separate the “Y” and “C” signals.

Found this on the web that will convert the S-video to HDMI with decent reviews. May be less hassle buying then building. https://www.monoprice.com/product?p_id=9994

The answer to your S-Video problem is one that is easy. Go to Amazon.com and look at these converters.

StarTech SVID2COMP 6-Inch S-Video to Composite Video Adapter Cable $2.06 each.

Electop 2 Pack S-Video Female to RCA Male Composite Video Adapter $6.59 (Prime) for a pair (very small device that I have used for years).

But your biggest worry is your S-Video machine. Start looking at the converters to put your tapes on your hard drive and a backup on a Thumb Drive for safe keeping, if your home movies are not replaceable.
Good Luck and a healthy New Year to you.

Vacuum tubes are resilient and can withstand over voltage better than solid state parts. Tube characteristics are dependent on the physical construction and don't change with voltage if the circuit is properly designed. If the radio has a power transformer, It certainly has a full wave rectifier. The 5Y3 has a tube drop of 60 volts so if it is replaced by a solid state rectifier, the DC output should be 60 volts higher. This is not significant when the nominal DC output is 300 volts. If you are worried about it, put a resistor in series.

The maximum voltage output from any rectifier is less than the peak voltage, so start from that end by measuring the RMS voltage of the AC power transformer output , and multiply that by 1.4 to get an average peak voltage. If it is less than the filter capacitor DC rating then you are safe to install any solid state rectifier that has a higher voltage and current rating. Anyway, replacing the filter capacitors is always a good idea due to aging.

You might look at tubesandmore.com. They have thousands of vacuum tubes.

Tube guitar amps use solid state rectifiers all the time, check out Mesa Boogie. I suspect they are more efficient, and the supply voltage may increase a bit, but my guess is that it’s not so dramatic as to destroy everything, maybe 10-20% increase.

If you can disconnect the rest of the receiver you can always try it and measure the before and after supply voltage, see if it’s still in a safe range. Be careful doing that, of course, it’s a high voltage power supply.

I think the filter capacitors are at a slight risk during the replacement procedure. But maybe they need replacement anyway.

First you need to know the existing rectifier output voltage, measured from a trial run or read from the instruction manual. Then you use silicon diodes to replace the tube rectifier. Re-measure the voltage and B+ current. Be careful these voltages can give you a memorable shock.

Then use Ohm’s law to calculate a resistor to put in series with the B+ line to return the B+ to near its original value. Don’t forget to calculate the power dropped by the resistor to make sure to get one of sufficient dissipation (watts) rating.

If you are uncomfortable with these steps, get a ham old-timer to help. The good side is you should improve reliability and save the power that went into the rectifier filament.

I would say it's a bad idea. Solid state rectifiers have a much lower internal resistance than tube rectifiers, resulting in significantly higher voltage. I'm surprised you can't find a replacement. What's the tube you need?

A solid state replacement will have a lower forward voltage drop than a tube, typically less than a volt. So, the rest of your circuitry will see a few extra volts. This is not likely to be a problem, however I would have another concern.

Using a solid state rectifier means that it will begin rectifying immediately upon power up, the rest of the tubes will NOT yet be conducting and therefore the entire circuit will be drawing very little current. This means that your power supply caps etc. will probably be seeing close to PEAK voltage until the tubes begin to conduct and draw current.

When using a tube rectifier; it too comes up slowly as the rest of the tubes do, you do not get the PEAK voltage anywhere. I’d stick with the tube rectifier; eBay and lots of other on line suppliers can get you one.

There’s some good material on this subject at www.antiqueradios.com/forums/viewtopic.php?p=973781.

I would also suggest that you look for your tube replacment at https://www.tubesandmore.com.

By the way, the latter site also offers their T-SSR01 solid-state replacement for 5Y3, 5U4 and 5AR4 tube rectifier, but please note the cavaeat in the part description.

In regards to your rectifier tube for the Hallicrafters Radio, I suggest you have a look at this website: https://www.tubesandmore.com/products/vacuum_tubes?filters=Type%3DRectifier

They have all kinds of older tubes, most are what is called New Old Stock. We could have provided more information as to use of a solid state rectifier replacement, but it would have helped to know the radio model number and the tube number you were replacing. Hope this helps you fix it.

A solid state rectifier will have less than a voltage drop, a tube is higher depending upon the tube and the current level, etc. This will result in a somewhat higher voltage to the circuitry, but not an awful lot.

There is, however, another situation to consider. When you power up with all tubes, they all come on slowly. Tubes begin to conduct plate current as the rectifier begins to work, sort of a “soft” start. With a solid state rectifier, it will begin immediately upon application of power, while the tubes are not yet consuming any current as they warm up.

This means that since drain on rectified supply is quite low until the tubes come up to speed, the power supply caps will charge pretty much to peak levels, which may exceed their ratings, or certainly stress them more than if you were using a tube rectifier.

I’d suggest sticking with a tube rectifier. You should be able to get one via eBay, or many other on line sources.

Also, a solid state diode has no warm up period. It means that full power supply voltage instantly is present on a circuit that may not be ready for it yet. It can be done, but replacement of a tube with a solid state diode may need some additional precautions (a heavy resistor in line may be enough). I say may, since there are definitely sets which are capable of absorbing this difference.

Most Hallicrafters sets were not the most rugged out there, many without the safety of power transformers. I’d be careful. On the other hand, I find it hard to think you would not be able to find a suitable tube on FleaBay or some of several tube vendors on line (Try Antique Electronic Supply).

You are correct in that there can be some issues to be considered when replacing a tube rectifier with a solid-state replacement. The primary issue is timing. A solid-state rectifier will provide the full B+ voltage almost immediately, while a tube rectifier needs to have the filament warm up, and the B+ voltage will come up much more slowly. Also, the other tubes which will use the B+ will need to warm up and be able to provide a suitable load for the B+. Without a load, the resistors in the supplies will not drop voltage as intended, and so the voltages at the plates of the consuming tubes will be much higher initially until those tubes warm up.

In addition, the tube rectifier has a “resistance” providing a voltage drop that the solid-state device will not. This means that the output of the power supply section will be at a higher voltage than that with a tube. The capacitors must be rated to handle the increased voltage, and the circuit will need to operate properly with the increased B+ voltage.

If the radio has not been operated in some time, it would be good to replace the filter capacitors at a minimum. Some solid-state replacements will include some internal resistors and thermistors (resistors that change value as they heat up) to approximate the characteristics of a tube rectifier. This type of replacement is usually best.

After installing the replacement, the B+ voltage should be checked against the normal expected voltage, and perhaps some of the resistance values in the power supply can be adjusted if needed.

The short answer is no. VGA is an analog interface, LCDs use a digital interface. You would need a 3 channel ADC to start with, but even that’s not enough. It would be very difficult to extract alphanumeric characters for the LCD from that data. Plus the 4x20 LCD is so small compared to the VGA display that there’s no way it can hold all the information shown on VGA.

You would be FAR better off rigging up some kind of serial port interface to the PC with the VGA output and selectively sending whatever data is of interest to the LCD.

In all honesty, I believe this would be a fruitless exercise. The interface would be far from simple, and the resulting image on the 4x20 LCD display would most likely not be recognizable from the original VGA image.

VGA has a resolution of 640 x 480 and the LCD display would be 100 x 28, assuming 5 x 7 matrix for each character. Keep in mind the LCD display consists of a 4 rows of 20 characters each. Each character is formed by a 5 x 7 dot matrix, and the characters are separated by approximately a pixel width and 0.2 pixel height. So you are going from an aspect ratio of 4:3 to 25:7 or 12.5: 3.5, a significant difference.

In addition the pixels in the VGA display can vary in color and brightness, where the LCD display is only black and white, and are not individually adjustable in brightness.

And finally, the electronic interfaces to drive each type of display are significantly different both in hardware and software, and would require a very complex interface to even come close.